Jump to content

Custom Search


Welcome to the Ford Fusion Forum


Sign In  Log in with Facebook

Create Account
Welcome to the Ford Fusion Forum
 
Like most online communities, you must register to create a topic, reply to a topic, post photos and more. Registration is free, simple and takes only a few minutes. 
 
By becoming a member, you'll be able to:
 
• Choose your own social group icon
• Start new topics and reply to posts
• Subscribe to topics and forums to get email updates
• Create your own profile page and make new friends
• Send personal messages to other members
• Create a photo album and upload your own photos. . more!

 
Choose your Ford Fusion Social Group!
 

Posted Image
 
Click here to register now
 
Guest Message by DevFuse

The official Ford Fusion Registry is live - more here.


Photo
- - - - -

"check accutrac system" warning


  • Please log in to reply
4 replies to this topic

#1 OFFLINE   jluke

jluke

    New Fusion Member

  • Fusion Member
  • Pip
  • 3 posts
  • Region:U.S. Southern Plains
  • Location:baton rouge, la
  • My Fusion:2010
  • Current Vehicle:2010 fusion
  • Social Group: myfusion

Posted 18 May 2017 - 06:41 PM

Today, this warning showed up on the dash of my 2010 Lincoln Mkz. Warning lights for the brakes and antiskid are also on. Brakes work fine, plenty of brake fluid, no codes thrown. I am posting there as the mkz is basically a dooded up Fusion, and there are few do it yourselfers on the Lincoln site. At first, engaging and disengaging the parking brake cleared the readout, but now the notice comes on after driving a short distance. Any ideas, or time to go the the dealor?









Lose this advertisement by becoming a member. Click here to create a free account.


#2 OFFLINE   drolds1

drolds1

    Fusion Forum Enthusiast

  • Moderator
  • 2,448 posts
  • Region:Decline
  • My Fusion:Decline
  • Social Group: myfusion

Posted 18 May 2017 - 08:13 PM

See my reply on the MKZ forum.  Check your battery.



#3 OFFLINE   jluke

jluke

    New Fusion Member

  • Fusion Member
  • Pip
  • 3 posts
  • Region:U.S. Southern Plains
  • Location:baton rouge, la
  • My Fusion:2010
  • Current Vehicle:2010 fusion
  • Social Group: myfusion

Posted 19 May 2017 - 06:26 AM

thanks, battery is a year old, but just checked the voltage, 12.5, which is a little low. Thanking that cracked copper multiconnector is not allowing the battery to fully charge. Have a charger on it now, when it.s up to 13 or more, I will test drive it and let you know the outcome



#4 OFFLINE   jluke

jluke

    New Fusion Member

  • Fusion Member
  • Pip
  • 3 posts
  • Region:U.S. Southern Plains
  • Location:baton rouge, la
  • My Fusion:2010
  • Current Vehicle:2010 fusion
  • Social Group: myfusion

Posted 19 May 2017 - 07:17 AM

fingers crossed, charged to battery to 100%, drove around the block, no lights. I will find out later today when  my wife drives around town, but I will pick up a new connector and install it. Will advise if I have more problems. Thanks Droid!



#5 OFFLINE   akirby

akirby

    Fusion Forum Fanatic

  • Moderator
  • 6,700 posts
  • Region:Decline
  • Location:Suwanee, GA
  • My Fusion:Decline
  • Current Vehicle:2013 Fusion Titanium Ruby Red
  • Social Group: myfusion

Posted 19 May 2017 - 07:26 AM

You can't go by voltage.  Get a Solar tester to check the cranking amps.  

 

If the problem returns and isn't the battery then it could be a wheel speed sensor or wiring.   You'll need to get the dealer to read the codes to see which wheel.  Check for a damaged wire - that has been reported more than once.


  • WWWPerfA_ZN0W likes this




Custom Search






Privacy Policy Terms of Service ·