Search the Community

I am looking for a Sunset Metallic (Orange) door lock cover for the driver side. Just the plastic cover for the door lock. Message me if you have one!

So I was driving down the highway when a tube of grease flew from the oncoming lane and absolutely tore this assembly up. has anyone ever replaced this cover (or even know how to) or have any idea how much ford will charge to fix it? Does the whole bumper need to be dropped to access this/ do I need to access it via the wheel well or can I somehow manage to change this from the outside? Disassembly will be a breeze because the part is pretty much in small pieces at this point, I just wonder how difficult it will be to reassemble... any feedback helps, thank you guys for everything!!!

Hi, I'm having an issue with my 2006 Fusion. The piano black door pillar post trim (passenger side, rear) has bent outwards, separated from the body of the car, and now becomes stuck on my front passenger doorframe every time I open the door. This has bent the trim panel & makes it difficult to open and close the door without causing more damage. The trim is bent now and looks awful, and I'm afraid to open my front passenger door. Has anyone ever seen this issue with a fusion before? Any advice as to how I should fix it? I'm including a picture showing the panels in question circled. Thanks in advance!

A-PILLAR TRIM OUT OF POSITION NEAR THE HEADLINER – FLAT ROCK ASSEMBLY PLANT – BUILT ON OR BEFORE 26-AUG-2016 Publication Date: September 1, 2016 FORD: 2014-2016 Fusion ISSUE: Some 2014-2016 Fusion vehicles built at the Flat Rock assembly plant and built on or before 26-Aug-2016 may exhibit an A-pillar trim panel out of position near the headliner at one or both front doors. ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Does the vehicle exhibit an A-pillar trim panel out of position near the headliner? (Figure 1) Figure 1 a. Yes – proceed to Step 2. b. No – this article does not apply. 2. Check the vehicle identification number (VIN). Does the first digit of the VIN start with the number 1? Refer to Workshop Manual (WSM), Section 100-01. a. Yes – proceed to Step 3. b. No – the vehicle was not built at the Flat Rock assembly plant. Refer to WSM, Section 501-05 for normal diagnosis. 3. Remove the lower interior B-pillar trim panel. Refer to WSM, Section 501-05. 4. Remove and discard the upper B-pillar trim panel. Refer to WSM, Section 501-05. 5. Remove the assist handle retainer covers and the retainers and remove the assist handle. 6. Remove the sun visor and sun visor clip. Refer to WSM, Section 501-05. 7. Remove and discard the upper A-pillar trim panel. Refer to WSM, Section 501-05. 8. Position the headliner down so the forward foam block/stuffer can be accessed. (Figure 2) Figure 2 9. From the outside edge of the foam, measure and mark 17 mm (21/32″). (Figure 2) 10. Using a hacksaw blade or equivalent, cut and remove 17 mm (21/32″) from the outside edge of the foam. (Figure 3) Figure 3 11. To install, reverse the removal procedure. PART NUMBER PART NAME W715667-S439 Trim Clip (Package 4) DS7Z-5403599-FB A-pillar Trim – Driver Side – Earth Gray DS7Z-5403598-FB A-pillar Trim – Passenger Side – Earth Gray DS7Z-5424356-AD B-pillar Trim- Driver Side – Earth Gray DS7Z-5424357-AD B-pillar Trim – Passenger Side – Earth Gray DS7Z-5424357-AC B-pillar Trim – Driver Side – Dune DS7Z-5424356-AC B-pillar Trim – Passenger Side – Dune DS7Z-5403599-AE A-pillar Trim – Driver Side – Dune DS7Z-5403598-AE A-pillar Trim – Passenger Side – Dune OPERATION DESCRIPTION TIME 160112A 2014-2016 Fusion: Measure And Cut The Foam Block/Stuffer At One (1) Front Door Following The Service Procedure (Do Not Use With Any Other Labor Operations) 0.6 Hr. 160112B 2014-2016 Fusion: Measure And Cut The Foam Block/Stuffer At Both (2) Front Doors Following The Service Procedure (Do Not Use With Any Other Labor Operations) 1.0 Hr. WARRANTY STATUS Eligible Under Provisions Of New Vehicle Limited Warranty Coverage. Warranty/ESP coverage limits/policies/prior approvals are not altered by a TSB. Warranty/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool. DEALER CODING BASIC PART NO. CONDITION CODE 5403598 07

I recently bought a preowned 2016 fusion. Long story short I love it. My only quirks is that the last owner scratched up the trim so its all chipped up and its very noticeable and it annoys me. I know how to remove the center dash trim but not the rest so if you can link me to videos on how to do that I'd greatly appreciate it. My real question is what color should I paint it. The car it magnetic metallic so im not thinking anything flashy. I want personality so i don't want to go straight to black. I appreciate any suggestions.

Does anyone know if the different trim levels of the 3rd gen Fusion have different style fog light bezels? I've been looking up parts to add fog lights to my 2015 SE and I've found the standard dimpled version, a smooth matte black version, and a glossy black version. Does anyone have a Titanium/Hybrid/Energi that can tell/show me what kind of bezels are on your car? Thanks!

So I've been trying my hardest to find a piece for the 2010+ Fusion that keeps the carbon fiber trim around my radio. All of the Metra and Scosche kits are one piece options that don't really match. But the other day I was watching some YouTube videos on radio installs, and came across this video: The problem is that the piece is from a company in Brazil and the whole site is in Portuguese (spell check). http://www.flashaudiostore.com.br/molduras/molduras-ford-fusion-2-dim.html Anyone know where else these may be available? And if not, anyone know Portuguese?! LOL! Seriously, I think this would help a lot of people out and look awesome in our cars.