HumanTorch4596 Posted June 29, 2022 Share Posted June 29, 2022 (edited) So the car sat overnight and it will only try and crank twice then I get an message that it is overheating. Does anyone have an idea where I should start looking? This is what I get from forscan, ===PCM DTC P1289:00-25=== Code: P1289 - Cylinder Head Temperature Sensor A Circuit High Status: - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Powertrain Control Module ===END PCM DTC P1289:00-25=== ===PCM DTC P2610:00-25=== Code: P2610 - ECM/PCM Engine Off Timer Performance Status: - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Powertrain Control Module ===END PCM DTC P2610:00-25=== ===OBDII DTC None=== Successful DTC reading, no error codes found Module: On Board Diagnostic II ===END OBDII DTC None=== ===APIM DTC None=== Successful DTC reading, no error codes found Module: Accessory Protocol Interface Module ===END APIM DTC None=== ===BdyCM DTC None=== Successful DTC reading, no error codes found Module: Body Control Module ===END BdyCM DTC None=== ===BECMB DTC None=== Successful DTC reading, no error codes found Module: Battery Energy Control Module B ===END BECMB DTC None=== ===FCIM DTC U0401:00-48=== Code: U0401 - Invalid Data Received from ECM/PCM A Status: - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC - Test not complete Module: Front Controls Interface Module ===END FCIM DTC U0401:00-48=== ===FCIM DTC U0401:81-48=== Code: U0401 - Invalid Data Received from ECM/PCM A Additional Fault Symptom: - Invalid Serial Data Received Status: - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC - Test not complete Module: Front Controls Interface Module ===END FCIM DTC U0401:81-48=== ===FCIM DTC U0401:82-48=== Code: U0401 - Invalid Data Received from ECM/PCM A Additional Fault Symptom: - Alive/Sequence Counter Incorrect/Not Updated Status: - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC - Test not complete Module: Front Controls Interface Module ===END FCIM DTC U0401:82-48=== ===FCDIM DTC None=== Successful DTC reading, no error codes found Module: Front Control/Display Interface Module ===END FCDIM DTC None=== ===OCS DTC None=== Successful DTC reading, no error codes found Module: Occupant Classification System Module ===END OCS DTC None=== ===ABS DTC None=== Successful DTC reading, no error codes found Module: Antilock braking system ===END ABS DTC None=== ===RTM DTC None=== Successful DTC reading, no error codes found Module: Radio Transceiver Module ===END RTM DTC None=== ===PDM DTC None=== Successful DTC reading, no error codes found Module: Passengers Door Control Unit ===END PDM DTC None=== ===DDM DTC None=== Successful DTC reading, no error codes found Module: Drivers Door Module ===END DDM DTC None=== ===RCM DTC None=== Successful DTC reading, no error codes found Module: Restraint Control Module ===END RCM DTC None=== ===GSM DTC None=== Successful DTC reading, no error codes found Module: Gear Shift Module ===END GSM DTC None=== ===PSCM DTC None=== Successful DTC reading, no error codes found Module: Power Steering Control Module ===END PSCM DTC None=== ===ACM DTC None=== Successful DTC reading, no error codes found Module: Audio Control Module ===END ACM DTC None=== ===SCCM DTC None=== Successful DTC reading, no error codes found Module: Steering Column Control Module ===END SCCM DTC None=== ===IPC DTC U0401:81-48=== Code: U0401 - Invalid Data Received from ECM/PCM A Additional Fault Symptom: - Invalid Serial Data Received Status: - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC - Test not complete Module: Instrument Panel Control Module ===END IPC DTC U0401:81-48=== ===IPC DTC U300A:64-0A=== Code: U300A - Ignition Switch Additional Fault Symptom: - Signal Plausibility Failure Status: - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Instrument Panel Control Module ===END IPC DTC U300A:64-0A=== ===GWM DTC None=== Successful DTC reading, no error codes found Module: Gateway Module A ===END GWM DTC None=== ===TRCM DTC None=== Successful DTC reading, no error codes found Module: Transmission Range Control Module ===END TRCM DTC None=== ===GPSM DTC None=== Successful DTC reading, no error codes found Module: Global Positioning System Module ===END GPSM DTC None=== Edited June 29, 2022 by HumanTorch4596 0 Quote Link to comment Share on other sites More sharing options...
akirby Posted June 29, 2022 Share Posted June 29, 2022 You could have stopped at cylinder head temp sensor. It’s bad. 0 Quote Link to comment Share on other sites More sharing options...
HumanTorch4596 Posted June 29, 2022 Author Share Posted June 29, 2022 2 hours ago, akirby said: You could have stopped at cylinder head temp sensor. It’s bad. That's what I'm hoping, I just ordered one. But honestly think that code is showing because I unplugged it and then turned the ignition on to see the codes, to see if anything changed. 0 Quote Link to comment Share on other sites More sharing options...
HumanTorch4596 Posted June 30, 2022 Author Share Posted June 30, 2022 11 hours ago, akirby said: You could have stopped at cylinder head temp sensor. It’s bad. Like I thought, it wasn't the issue. I have cleared all codes and this is what shows up before and after I tried to start it. after start attempt.txt Before Start.txt 0 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.